Here at 2h Storage we often get asked to install mezzanine floors with offices above and below, these are examples of typical specifications for Mezzanine floors with offices.

 

 

Supply and install mezzanine to include stair case and 3.5 linear mtrs of hand rail. (need for hand rail above fridge area to be confirmed with building control)

 

Supply, deliver and install 75mm Monoblock insulated panel system partition fixed from floor to
underside of mezzanine deck – 2762mm high.

 

Panels to be faced both sides with food safe laminate in white finish, base and head steel
sections to be in SAA finish.

 

Panels interlock with system profiling to negate the need to fix a trim or silicone beading to
panel joints.

 

 

1 No. single (1981 x 838 x 44mm) and 1 No. double (1981 x 1676 x 44mm) doorset to be
included, door frames to be aluminium wraparound profile with integral hinges powder coated
white. Doors to be Light Oak veneer, solid core to FD30 with clear vision panel 1500 x 150 and
satin stainless ironmongery comprising of 300mm bolt through D handle, 330mm push plate and
over head door closer.

 

1a: Form “pocket” detail for sliding door
Form return wall on monoblock system to form a void for fridge sliding too to operate into.

 

Electrical Installation
Taking supplies from adjacent Hager distribution board and providing new circuit breakers to
same;
Install 10 No. twin switched 13 amp sockets surface mounted on partition or existing building
walls.
Install 4 No. twin tube fluorescent light fittings with sealed prismatic diffusers to underside of
suspended ceiling with wiring in ceiling void.

 

Partitioned office to mezzanine level
Install 75mm demountable partition nominally 3400 x 4000mm including 2 No. glazed modules
from dado to doorhead glazed in 6.4mm laminate glass to approved document N of the building
regulations. And 1 No. single (1981 x 838 x 44mm) doorset to be included, door frames to be
Aluminium wraparound profile with integral hinges powder coated white. Doors to be Light Oak
Veneer, solid core to FD30 with clear vision panel 1500 x 150 and satin stainless ironmongery
comprising of round bar lever handles and cylinder lock.
Partition panels to be decorated in paper backed vinyl wall covering from the Dixon Turner
“Newmarket” range. Suspended ceiling over area to be mineral fibre 600 x 600 tiles in 24mm
exposed T grid system.

 

Electrical installation to office
Install recessed modular light fittings with category 2 louvers, emergency lighting provision and
4 No. 13 amp twin switched socket outlets into partition panels.

 

Fire protection to mezzanine
Install pre formed fire rated column casings and fascia to mezzanine construction and fire rated
suspended ceiling to underside of mezzanine to provide one hour integrity to structure as is
required with office accommodation upon a mezzanine.

 

Mezzanine Floor structure and installation.
Fire protection to mezzanine:
Install pre formed fire rated column casings and fascia to mezzanine construction and fire rated suspended ceiling to underside of mezzanine to provide one hour integrity to structure as is required with office / amenities accommodation upon a mezzanine.
Builders work
Form 2 No. new opening in single leaf, non-load bearing block work fitting pre stressed concrete
lintel across opening to support remaining block work above. Line out reveals and fit stop lat and architraves, install FD30s oak veneer doors with satin stainless ironmongery and overhead self-closing mechanism. Make good locally to disturbed plaster finishes.

 

Partitions + Dry lining
Install 75mm demountable partitions to 2700mm high comprising of steel studs @ 600mm
centres with one layer of 12.5mm plasterboard either side, insulation to void. 6 No. aluminium windows with glazing to part N of building regulations (glass safety). 1 No. 1981 x 838 x 44mm oak veneered door with satin stainless ironmongery and overhead self closing mechanism.
All exposed aluminium sections are to be powder coat finish in either light grey or white.
Dry lining to block work walls within area of new office and canteen to match partition system. All solid panels to receive decoration from the Dixon Turner “Newmarket” range of paper backed vinyl wall covering.

 

Electrical Installation
Taking supplies from distribution within 5 metres of installation:
Install surface mounted lights to underside of mezzanine with emergency lighting provision.
Install recessed modular light fittings to offices and canteen area on mezzanine with emergency lighting provision.
Install 9 No. 13 amp twin switched socket outlets to canteen and offices at mezzanine level.
All electrical works to BS7671, 18th addition by fully qualified and experienced electrician, all installation works to be tested and certified on completion.
Mezzanine level ceiling
Install 600 x 600 24mm exposed white T grid system and lay in 600 x 600 fissured white suspended ceiling tiles. Perimeter to be finished with 19 x 29 steel angle trim painted white.
Lay over back Isowool insulation matting to retain thermal properties and reduce sound transference.
Flooring
To canteen area lay Polyflor Polysafe Xlpu homogenous sheet vinyl flooring on permanent adhesive.
To office areas lay Desso Essence carpet tiles on F41 release adhesive.

 

Kitchen
Install sink base and base units, inset stainless steel sink and drainer, plinth sections, 38mm worktop, make plumbing and waste connections into services assumed to be immediately adjacent.
Fork lift truck hire option for us to use your FLT
Building regulation : P.C. sum to be confirmed prior to contract.